9 0 3 4 0 D 2 D I A M O N D . 3 4 0 0 MAXTOR Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 11530| | | Capacity form/unform 3400/ MB Heads 2| | | Seek time / track 9.0/ 0.9 ms Sector/track | | | Controller IDE / ATA4 Precompensation Cache/Buffer 256 KB SDRAM Landing Zone Data transfer rate 18.600 MB/S int Bytes/Sector 512 33.000 MB/S ext Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 71 Power: sleep W Humidity % 5 95 | 5 95 standby 0.9 W Altitude km -0.061 3.048| -0.061 12.192 idle 4.4 W Shock g 20 | 200 seek 9.6 W Rotation RPM 5400 read/write 4.8 W Acoustic dBA 36 spin-up 20.2 W ECC Bit MTBF h 500000 Warranty Month 36 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR DIAMOND MAX 3400 Pin 1 J1 IDE Connector | J2 Power +----------- --------+-++-----------++---------+ | .................... || @ * * * || X X X X | | .......... ......... || @ * * * * || X X X X | +----------------------++-+-+-+-+-+-++-+-+-+-+-+ | | | | | | | | | | | | | | | | | | J50 Master/Slave -----+ | | | | | | | +-+12V J48 Cable Select -------+ | | | | | +---+12V Return J46 4092 Cyl Limitation---+ | | | +----- +5V Return J44 Factory Reserved -------+ | +------- +5V J42 Factory Reserved ---------+ ********************************************************************** J U M P E R S ********************************************************************** MAXTOR DIAMOND MAX INSTALLATION SHEET Jumper Setting ============== +---+---+---+---+---+ |J50|J48|J46|J44|J42| +-------------------------------------+---+---+---+---+---+ | Master/Slave | | | | | | | Only Drive in single drive system* | J | | | | | +-------------------------------------+---+---+---+---+---+ | Master in a dual drive system* | J | | | | | +-------------------------------------+---+---+---+---+---+ | Slave in a dual drive system | O | | | | | +-------------------------------------+---+---+---+---+---+ | Cable Select | | | | | | | Disabled* | | O | | | | +-------------------------------------+---+---+---+---+---+ | Enabled | | J | | | | +-------------------------------------+---+---+---+---+---+ J=Jumpered O=Open *=Default ********************************************************************** I N S T A L L ********************************************************************** MAXTOR 91360D8/91190D7/91020D6/90845D5/90680D4/90510D3/90340D2 Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Idle The drive is spinning., the actuator is parked and powered off, and all other circuitry is powered on. The drive is capable of responding to read commands within 40 ms. Read/Write Data is being read from or written to the drive. Spin-up The drive is spinning up following initial application of power and has yet not reached full speed. Maximum current draw lasts one second. Standby The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires disk access. The time-out value for this mode is programmable. The buffer is active to accept write data. Sleep This is the lowest power state - with the interface set to inactive. A software or hardware reset is required to return the drive to the standby state. ********************************************************************** G E N E R A L ********************************************************************** MAXTOR IDE INSTALLATION INSTALLATION PROCEDURE FOR AN IDE DRIVE --------------------------------------- 1. Install a 40 pin Data Cable ensuring that pin 1, which can be identified by the striped edge of the cable, is closest to the power connector on the drive. 2. Install a DC power cable to the back of the drive. 3. Verify the jumper configurations for Master/Slave operation (Note: Master will be the bootable drive. The slave will not be bootable.) Also make sure the existing C: drive is jumped to be the Master in a two drive system, not the only drive in the system. 4. Apply power to the computer. 4a. When memory test is complete go into your system's Standard CMOS set-up. (Note: There are various ways to get into CMOS set-up, please refer to system's manual for instructions.) 4b. If your system's BIOS supports a user programmable drive type, program the BIOS with the default parameters of your drive. If your system does not support a user programmable drive type choose parameters that closely match but do not exceed the drives MegaByte capacity. Escape from set-up then choose write to CMOS and exit. 5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on it. At the A> prompt type in FDISK. At the menu options select option 1 to create a DOS partition. Another menu will appear and from those options choose 1 to create a Primary DOS partition. Select yes to make 1 large partition and it will automatically become active. Then escape from FDISK. 6. At the A> prompt type in FORMAT C:/S This does a high-level format on the drive and transfers the system files in order for the drive to be bootable. (Note: IDE drives are low-level formatted from the manufacturer and only need a high-level format). To configure the drive as a slave drive repeat steps 1-4 and proceed with steps 5a. and 6a. as follows: 5a. At the C> prompt type in FDISK. When the menu options appear select option 5 to switch to the second drive. Enter fixed disk drive number 2. Then choose option 1 to create a DOS partition, then select option 1 again to create a Primary DOS partition or option 2 to create an Extended DOS partition. (Note: C and D drives will always be the Primary partitions but only the Primary partition on C: will have a status of active). 6a. Proceed with a high-level format on the drive by typing FORMAT D: (Note: Make sure the correct drive letter has been selected for format). 7. The drive is now bootable. As a test remove the DOS diskette from A and press reset to reboot the computer, a C> should be displayed, the drive is now ready for operation.