=============================================================================== 71626AP 3.5" IDE DRIVE =============================================================================== KEY FEATURES: * <12ms average seek * 128K on-board buffer * Low power consumption * Zone density recording * 1:1 interleave * Dual drive master/slave support * Rotary voice coil * Automatic actuator lock * Single-sided surface mount PCBA * 4480 RPM Rotational speed * EPA Energy Star compliant * MaxCache buffer management SPECIFICATIONS: Formatted capacity: ........................ 1,629,831,168 Bytes 1,554 Megabytes Bytes per sector:........................... 512 Integrated Controller/Interface: ........... AT Actuator type: ............................. Rotory Voice Coil Number of Disks: ........................... 3 Data Surfaces: ............................. 6 Data Heads: ................................ 6 Data Zones per Surface: .................... 10 Servo: ..................................... Embedded Number of Cylinders: ....................... 3,721 Sectors per Drive (user): .................. 3,183,264 Track Density (tpi): ....................... 4,232 average Flux Density (kfci): ....................... 61.42 maximum Recording Density (kbpi): .................. 92.13 maximum Encoding Method: ........................... RLL 1,7 Buffer Size: ............................... 128K Interleave: ................................ 1:1 PERFORMANCE: Seek performance (including settling time and servo overhead)* Seek times* (ms) Track to track: ....................... 2 Average: .............................. <12 ** Maximum: .............................. <25 Spindle speed (+-0.1%): .................... 4840 RPM Average latency (ms): ...................... 6.7 Controller overhead: ....................... 0.3 ms Data transfer rate (Mbytes per sec) To/From Media (MB/sec): .................. 4.61 - 8.10 To/from Host (without I/O CHRDY): ........ PIO Mode 3, 11.1MBs To/from Host (with I/O CHRDY): ........... PIO Mode 4, 16.6MBs DMA Transfers (sustained) ................ Mode 0 w/o DMARQ DMA Transfers (burst) .................... Mode 1 with DMARQ Start time (0 - Drive Ready) Average .................................. <9.85 sec Maximum .................................. <20 sec Stop Time/Power Down: Average .................................. <3.9 sec Maximum .................................. <6 sec Power Requirements - Two Disk (Average) Mode +12VDC +-8% +5VDC +-5% Power ---- ----------- ---------- ------- Spin-up** 1.24A 331mA 6.69W Read/Write* 231mA 453mA 5.04W Active* 408mA 425mA 7.02W Idle* 198mA 405mA 4.40W Standby* 0.96mA 253mA 1.28W Sleep* 1.02mA 199mA 1.01W Maximum power supply ripple allowed: 100 mV peak to peak, 0-20 MHz * Total RMS ** 1 second maximum Power Mode Definitions: ----------------------- Spin-up The drive is spining up following initial application of power and has yet not reached full speed. Maximum current draw lasts 3.8 seconds. Read/Write Data is being read or written to the drive. Active The drive is spinning and most circuitry is powered on. The drive is capable of responding to read commands in the shortest possible time. Read/Write heads are positioned over the data area. Idle The drive is spinning., the actuator is parked and powered off, and all other circuitry is powered on. The drive is capable of responding to read commands within 40ms. Standby The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires disk access. The time-out value for this mode is programmable. The buffer is active to accept write data. A program called GREENDRV.ZIP is available on the Maxtor BBS (303-678-2222), that will allow you to program this delayed standby mode. Sleep This is the lowest power state. The interface becomes inactive. A software or hareware reset is required to return the drve to Standby. Physical: Height: 1.00" ( 25.4 mm) Length: 5.75" (146.1 mm) Width: 4.00" (101.6 mm) Weight: 1.2 lb. (0.5 kg) Environmental: Temperature (Degrees C) Operating (stabilized).................. 5C to 55C Thermal gradient 20C/Hr max Non-operating/Storage .................. -40C to 71C MIL-STD-810E Method 502.3 & 501.3 Humidity *** Operating .............................. 5% to 95% non-condensing Non-operating/Storage .................. 5% to 95% non-condensing Thermal Shock Low Temperature (-20C to +25C) ......... MIL-STD-810E Method 503.3 High Temperature & Humidity ............ MIL-STD-810E Method 503.3 (+35C, 80%RH to +25C, 50%RH) Altitude (relative to sea level) Operating .............................. -200 to 10,000 feet Non-operating .......................... MIL-STD-810E Method 503.3 Reliability and Maintenance: MTBF ................................... >300,000 hours AFR .................................... <=2.9% Preventative Maintenance ............... None Component design life .................. 5 years (minimum) Error Rate ............................. <1 per 10^13 bits read Start/Stop Cycles....................... >40,000 Quality Acceptance Rate ................ 99.8% (2,000 DPPM) Shock & Vibration (typical): Operating Shock ........................ 34Gs 3ms (no errors) Non-Operating Shock .................... 120Gs 2ms (no errors) Operating Vibration - Swept Sine 1 Octave/min (without non-recoverable errors) 5-20Hz ............................... .049" Double amplitude 20-300Hz ............................. 2.5G P-P Apmlitude Non-operating Random Vibration - Swept sine 60 min/axis (without non-recoverable errors) 10 Hz ................................ 0.015 G^2/Hz 40 Hz ................................ 0.015 G^2/Hz 500 Hz ............................... 0.000015 G^2/Hz Acoustic Noise: Sound power (per ISO 7779) ............. 3.5 dBA Loudness (per ISO 532 B) ............... 1.26 sones Sharpness (proposed ANSI standard) ..... 1.56 Acums * At nominal DC input voltages ** The average of 10,000 random seek times (measured on independent test equipment) constitutes the average seek time specification. *** Operating and non-operating specs meet MIL-STD-810E. Method 507.3 Table 507.3-I High humidity diurnal category. Natural, High Humidity, Cyclic (Cycle 3) ============================================================================== 71626AP JUMPER DESIGNATION #J24#J23#J20# +---------------------------------------------#---+ # Cable Select # # # # # Disabled* # O # # # # Enabled # J # # # +-------------------------------------------------+ # Write Cache # # # # # Enabled* # # O # # # Disabled # # J # # +-------------------------------------------------+ # Master/Slave # # # # # Only drive in single drive system* # # # J # # Master in dual drive system* # # # J # # Slave in dual drive system # # # O # +-------------------------------------------------+ J=Jumpered O=Open *=Default Note: Jumpers J21 & J22 are factory reserved, do not use. A spare shunt is shipped between J23 & J24. +----\ /---------------\ /--\ /-------------\ /--\ /--------+ # ---- ------ --- ------ --- # # +---+ # +------+ -# # # + V--------------------------------> ##:::::# -# # # +-----------------+ +------+ -# # # # J21 J23 # + -# # # # +-----------+ # -# # # # # * 0 0 *** # # -# # # # # * 0 0 0 0 # # -#J1 # # # +-----------+ # -# # # # J20 J22 J24 # -# # # +-----------------+ -# # # -# # # -# # # 1 # # # +---# # +----# # + + 1 # # # 2 # # # 3 # J2 # # ---- ------ --- ------ --- 4 # # +----/ \---------------/ \--/ \-------------/ \--/ \---------+ =============================================================================== Power and IDE interface connections: # J1 # # J2 ___________________Data__________________ # # ____Power___ # . . . . . . . . . . . . . . . . . . .# # #/ \=# 1 . . . . . . . . . . . . . . . . . . .#=====# ## O O O 1 # #___________________ ___________________# # ##____________# # # +5 G G +12 # #===============================================================# =============================================================== "Back" of typical Maxtor 7000A Series IDE Hard Drive Showing Data and Power connector orientation Red or Blue stripe on 40 pin ribbon cable=pin 1 Power cable: +5=Red Grounds=Black +12=Yellow =============================================================================== The serial number is located on the lower left corner of the Maxtor Label. This label is located on the side opposite the printed circuit board. The serial number is also located on a barcoded label on the "front" of the drive, and also on the retail box. The serial number is made up of alpha-numeric charaters, for example: A30025PR =============================================================================== CMOS Configuration: Cyls Hds Write Landing Sec/Trk PreComp Zone ---------------------------------- 3158 16 0 0 63 71626AP is a trademark of Maxtor Corporation. AT is a registered trademark of IBM Corporation. Specifications subject to change without notice. Copyright 1995 Maxtor Corporation. Rev A 7/24/95 T.Brooker ================================================================================